NIBE ground source heat pump

NIBE F1126

Ground source heat pump
  • Product information
  • Advantages

NIBE F1126 is an all-in-one heat pump without integrated hot water tank, which makes it easy to install in locations with low ceilings. A separate hot water tank is selected according to hot water requirements. The heat pump is suitable for detached and terraced houses. NIBE F1126 has an efficient compressor which provides high annual efficiency. The heat pump is available in the output sizes 6, 8 and 12 kW. NIBE F1126 is equipped with a control unit for reliable operation. A large backlit display uses icons and text to display clear information about status, operating time and all temperatures in the heat pump.

Suitable for low ceilings

Easy-to-install heat pump with hot water tank selected according to requirements.

Efficient heating

Efficient compressor ensures a high seasonal performance factor.

Reliable and user friendly

Reliable operation and user-friendly display.

  • Accessories
  • Technical data
  • Document
NIBE F1126-8
NIBE F1126-12

NIBE EXC 40

Extra relay card required if ground heat pump and/or hot water circulation pump is to be connected to F1226. The extra relay card is installed inside the heat pump.

NIBE FLM - Console package

FLM - Console package

NIBE EF 45

Extension frame.

This accessory is used for the wall mounting of NIBE's compatible products SAM 40, SAM 41, FLM, F135 and Split installation of F730/F750

NIBE NV 10

Level monitor of brine collector circuit.

NIBE KB 25

Combination valve for filling up the brine. Including insulation. For heat pumps max. 12 kW.

NIBE OPT 10

NIBE OPT 10 is used to enable connection and control of gas boiler NIBE GBM 10-15

NIBE FLM

The NIBE FLM is an exhaust air module with built-in fan, specially designed for combining recycling of mechanical exhaust air with a NIBE ground source heat pump, providing an integrated solution for ventilation, hot water and heating. The NIBE FLM has a high fan capacity and low noise level. Energy is recovered from the ventilation air; even when the heat pump is not in operation, energy is stored in the ground or soil collector and exhaust air energy is thus put to maximum use. Thanks to smart technology, the product gives you control over your energy consumption and will be a key part of your connected lifestyle. The efficient control system automatically adjusts the indoor climate for maximum comfort, and you do nature a favour at the same time.

NIBE PLEX 310-20

Tap water exchanger.PLEX is a plate heat exchanger with plates manufactured from acid-resistant steel (SS 23 43). PLEX is available in seven different models. Insulation, consisting of two 30 mm-thick, moulded halves of polyurethane foam, corresponding to approx. 70 mm mineral wool, is included. The surface is covered by ABS plastic.

NIBE Top cabinet 245 mm

Top cabinet

NIBE RTS 40

Room sensor used to obtain a more even indoor temperature. RTS 40 has up to three functions:Show current room temperature in the heat pump's display. Option of changing the room temperature in °C. Makes it possible to change/stabilise the room temperature.

NIBE PLEX 322-60

Tap water exchanger.PLEX is a plate heat exchanger with plates manufactured from acid-resistant steel (SS 23 43). PLEX is available in seven different models. Insulation, consisting of two 30 mm-thick, moulded halves of polyurethane foam, corresponding to approx. 70 mm mineral wool, is included. The surface is covered by ABS plastic.

NIBE PLEX 322-40

Tap water exchanger.PLEX is a plate heat exchanger with plates manufactured from acid-resistant steel (SS 23 43). PLEX is available in seven different models. Insulation, consisting of two 30 mm-thick, moulded halves of polyurethane foam, corresponding to approx. 70 mm mineral wool, is included. The surface is covered by ABS plastic.

NIBE PLEX 322-30

Tap water exchanger.PLEX is a plate heat exchanger with plates manufactured from acid-resistant steel (SS 23 43). PLEX is available in seven different models. Insulation, consisting of two 30 mm-thick, moulded halves of polyurethane foam, corresponding to approx. 70 mm mineral wool, is included. The surface is covered by ABS plastic.

NIBE PLEX 310-80

Tap water exchanger.PLEX is a plate heat exchanger with plates manufactured from acid-resistant steel (SS 23 43). PLEX is available in seven different models. Insulation, consisting of two 30 mm-thick, moulded halves of polyurethane foam, corresponding to approx. 70 mm mineral wool, is included. The surface is covered by ABS plastic.

NIBE PLEX 310-60

Tap water exchanger.PLEX is a plate heat exchanger with plates manufactured from acid-resistant steel (SS 23 43). PLEX is available in seven different models. Insulation, consisting of two 30 mm-thick, moulded halves of polyurethane foam, corresponding to approx. 70 mm mineral wool, is included. The surface is covered by ABS plastic.

NIBE Top cabinet 345 mm

Top cabinet

NIBE Top Cabinet 395-635 mm

Top cabinet

NIBE PLEX 310-40

Tap water exchanger.PLEX is a plate heat exchanger with plates manufactured from acid-resistant steel (SS 23 43). PLEX is available in seven different models. Insulation, consisting of two 30 mm-thick, moulded halves of polyurethane foam, corresponding to approx. 70 mm mineral wool, is included. The surface is covered by ABS plastic.

NIBE HR 10

Auxiliary relay HR 10 is a connection box housing a contactor and a rotary selector switch. It is used to control external 1 to 3-phase loads such as oil burners, immersion heaters and pumps.

Height (mm)

1500

Depth (mm)

620

Net weight (kg)

185

Product efficiency class room heating, 35 °C

A++

Product efficiency class room heating, 55 °C

A++

System efficiency class room heating, 55 °C

A+++

System efficiency class room heating, 35 °C

A+++

Efficiency class water heating

A

Refrigerant amount, CO2 equivalent (ton)

3,9

Declared tap profile

XXL

User manual
Installer manual
Product catalogue Ground source heat pumps
Energy Labels F1126-12
Energy Labels
Energy Labels