NIBE S735

NIBE BAU 10

Wall console for wall mounting.

NIBE OEK S20

The OEK S20 enables NIBE S735 and S735C exhaust air heat pumps to increase usable heating capacity by intelligently mixing outdoor air with the home’s exhaust air stream. By introducing outdoor air through a dedicated duct fitted with a motorised damper and an ambient temperature sensor, the main unit can adapt ventilation behaviour based on outdoor conditions, switching seamlessly between mixed air and exhaust only operation to protect performance and system safety.

NIBE DKI S10

This accessory is used when the heat pump is installed in a room with low ceiling height or when for some other reason you want to share the heat pump. After dividing, the lower part of the heat pump becomes 1500 (S735) mm high.(Height, upper part: 674 mm).

NIBE RMU S40

The NIBE RMU S40 is a room unit with 2,8” touch display with built in temperature and humidity sensors. It is used to control and monitor your NIBE S series heat pump/indoor module from another room in the house than the room where the heat pump is placed.

The NIBE S Series is a natural part of your connected home. Smart technology adjusts the indoor climate automatically while you’re in complete control from your phone or tablet. Giving maximum comfort and minimum energy consumption, while doing nature a favour at the same time.

NIBE EME 20

Communication module that translates Modbus RTU, from a solar inverter, to Modbus TCP/IP, for the heat pump to control the solar inverter

NIBE CAB S12

Floor stood cabinet to support the SAM S42

NIBE DEW S43

NIBE DEW S42

The NIBE DEW S42 is a complete docking kit that allows installers to connect the S735 exhaust air heat pump to the VPB S200 hot water cylinder. Supplied with a dedicated AXC control module, diverter valve, shut-off valve, check valve and a full set of immersion sensors, the DEW S42 provides all the hydraulic and electrical components necessary for reliable hot water integration. With pre-configured wiring looms, labelled connectors and factory-mounted communication cabling, the DEW S42 ensures a straightforward, standards-compliant installation.

NIBE AXC 20

NIBE SRV 10

The SRV 10 is a wireless radiator thermostat designed to give finer room level control within NIBE S-Series heating systems. Installation is straightforward: the unit is fitted onto an M30x1.5 radiator valve using the supplied adapter if required, then automatically enters its mounting and calibration phases. Local comfort can be adjusted directly at the radiator using the plus and minus keys, with the LCD screen providing clear feedback on operating mode, set temperature and battery status.

NIBE SAM S42

The SAM S42 is a dedicated supply air module designed to expand the capabilities of the NIBE S735 and S735C exhaust air heat pumps by adding tempered supply air ventilation. The unit incorporates a water to air coil, buffer vessel and dedicated circulation pump to preheat outdoor air before it enters the dwelling, improving comfort. Installation is straightforward, with wall or cabinet mounting options and clear pipework and ducting provisions, including separate connections for outdoor air and supply air.

NIBE TOC 40 Top cabinet 245 mm

The TOC 40 top cabinets provide a practical and visually clean way to conceal ventilation ducting and services above NIBE indoor units. Designed to match the width and depth of a wide range of products, they create a seamless, built-in appearance while maintaining the required 3 mm clearance from the main front panel for correct operation. Installers can select from fixed-height versions of 245 mm or 345 mm for standard ducting runs, or choose the 385–635 mm adjustable model when additional height is needed.

NIBE TOC 40 Top cabinet 345 mm

The TOC 40 top cabinets provide a practical and visually clean way to conceal ventilation ducting and services above NIBE indoor units. Designed to match the width and depth of a wide range of products, they create a seamless, built-in appearance while maintaining the required 3 mm clearance from the main front panel for correct operation. Installers can select from fixed-height versions of 245 mm or 345 mm for standard ducting runs, or choose the 385–635 mm adjustable model when additional height is needed.

NIBE TOC 40 Top Cabinet 385-635 mm

The TOC 40 top cabinets provide a practical and visually clean way to conceal ventilation ducting and services above NIBE indoor units. Designed to match the width and depth of a wide range of products, they create a seamless, built-in appearance while maintaining the required 3 mm clearance from the main front panel for correct operation. Installers can select from fixed-height versions of 245 mm or 345 mm for standard ducting runs, or choose the 385–635 mm adjustable model when additional height is needed.

NIBE TOC 40 445 mm

The TOC 40 top cabinets provide a practical and visually clean way to conceal ventilation ducting and services above NIBE indoor units. Designed to match the width and depth of a wide range of products, they create a seamless, built-in appearance while maintaining the required 3 mm clearance from the main front panel for correct operation. Installers can select from fixed-height versions of 245 mm or 345 mm for standard ducting runs, or choose the 385–635 mm adjustable model when additional height is needed.

NIBE CDS 10

This wireless sensor allows you to read the CO2, temperature and humidity level in a room or climate zone using the myUplink app. For NIBE S-series heating installations with ventilation the indoor comfort level can automatically be adjusted to give you a comfortable indoor climate. For example, you can increase ventilation and lower the CO2 level when there are a lot of people present or lower the ventilation to further reduce your energy costs. Because it is battery powered, it is easy to install, but it can also operate with an external power source using a micro USB.

Mount the sensor in your room and connect it to your NIBE S-Series heat and ventilation installation.

NIBE RPP 10

Enhances the signal, improving communication between your smart home products when they are placed at a distance from each other. For NIBE S- Series heating installations, the repeater functions as a switch, giving you the opportunity to control it remotely, schedule On and Off times and measure energy consumption.

Plug in the repeater and connect it to your NIBE S-Series heating installation.

NIBE ROT 10

The wireless room thermostat allows you to read and control the temperature of a room or a climate zone from the display of the room thermostat or via the myUplink app in your smartphone. For instance by increasing the hot water production when you have many guests or lower the ventilation for better savings when you are not home. Because it is powered by a rechargeable battery, it is easy to install.

Mount the thermostat in your room and connect it to your NIBE S-Series heat pump.

NIBE ECS 40

ECS 40 is used when heat pump is installed in houses with up to four different climate systems that require different flow line temperatures, for example, in cases where the house has both a radiator system and an under floor heating system.

NIBE THS 10

This wireless sensor allows you to read the temperature and humidity in a room or climate zone using the myUplink app. On the heat pump you can see the current room temperature or change it in °C. THS 10 replaces the fixed indoor sensor. Because it is battery powered, it is easy to install.

Mount the sensor in your room and connect it to your NIBE S-Series heating installation.

NIBE EF 45

Extension frame.

NIBE ECS 41

The NIBE ECS 41 kit allows installers to add one or more additional heating circuits to a NIBE heat pump installation where different supply temperatures are required, such as radiator and underfloor heating combinations. Each kit includes a dedicated AXC accessory module, shunt valve, shunt motor, circulation pump and temperature sensor, enabling the new zone to run as a fully controlled climate system with independent flow temperature, heating curve and pump operation. The ECS 41 is sized for larger UFH areas above 80 m².