NIBE SMO 40

NIBE ERS 30-400

The NIBE ERS 30-400 is a heat recovery ventilation unit with high temperature efficiency up to 94% and low energy consumption. The heat recovery ventilation unit is used in houses with areas up to approx. 350 m2. The NIBE ERS 30-400 is designed for installation with a NIBE ground source heat pump or a NIBE air/water heat pump for a complete heating and ventilation system. The heat recovery ventilation unit is easily controlled by the heat pump. Thanks to smart technology, the product gives you control over your energy consumption and will be a key part of your connected lifestyle. The efficient control system automatically adjusts the indoor climate for maximum comfort, and you do nature a favour at the same time.

NIBE F135

The NIBE F135 is an exhaust air module designed for docking to a NIBE air/water heat pump and a NIBE indoor module (VVM) or control module (SMO). The NIBE F135 uses the heat that is found in the house’s ventilation air to heat the house and hot water, at the same time as ventilating the house. In installations with cooling, hot water and cooling can be produced at the same time. The exhaust air module provides an improved seasonal performance factor and has a low noise level and high ventilation capacity. The NIBE F135 is easy to control through the heat pump’s indoor module. When combined with a NIBE heat pump, it gives you control over your energy consumption and will be a key part of your connected home. You will do the environment a favor while main­taining all the comfort in your home.

NIBE ELK 213 EXP

The NIBE ELK 213 acts as source of supplementary heat for NIBE heat pump systems, for up to 13kW output. It integrates seamlessly with NIBE systems, allowing the heat pump to activate electric backup automatically during peak loads, cold weather or rapid reheat periods. Multi-stage output control ensures smooth modulation and avoids unnecessary electrical demand. It also incorporates built-in safety features, including thermostats, temperature limiters and circuit protection, making the range suitable for compliant, predictable and installer-friendly system design.

NIBE SOLAR 40

NIBE SOLAR 40 enables solar heating with your heat pump. With additional solar panels and VPAS you get a complete system.

NIBE AXC 30

The VCC range provides the dedicated hydraulic reversing valve required to enable active cooling in NIBE four pipe installations. By using the QN12 motorised valve, the VCC 11 diverts the heat pump’s charge flow toward the cooling circuit whenever cooling mode is activated, while returning flow to the heating system at all other times. The actuator mounts using a simple adapter and spring clip system, allowing quick assembly on site, and switches position in around eight seconds to maintain stable cooling performance. VCC 11 is rated for up to 17kW cooling output.

NIBE CPD 11-25/75

The CPD 11-25/75 is a high-efficiency circulation pump, rated to 7.5 bar, designed to ensure stable and reliable flow within NIBE heating and cooling systems. Supplied as a compact, pre-assembled pump unit, it provides consistent circulation for underfloor heating, radiator circuits, buffer charging and other secondary loops where dependable flow is essential for correct heat-pump operation.

NIBE EMK 500

The NIBE EMK 500 energy metering accessories provides installers with a reliable way to monitor the actual energy delivered by a NIBE heating system, measuring both flow and temperature difference within the charge circuit to determine output for heating, domestic hot water or additional climate zones. The kit includes a precision flow meter, pre-terminated communication cable and the necessary pipework and unions for straightforward installation. The EMK 500 is suitable for higher-flow systems.

NIBE K11

The NIBE K11 control box provides installers with a complete and dependable electrical control solution for IU immersion heaters, combining an adjustable thermostat with a three-pole safety temperature limiter for secure and compliant operation. The unit is internally pre-wired and uses a clear, structured terminal layout to simplify electrical connection and reduce commissioning time.

NIBE VST 20

Makes hot water priority possible at large heat pump outputs. (charging power between 15 and 40 kW), together with an SMO 10 and F1330-40. This also requires a hot water accumulator, for example, NIBE VPA.

NIBE IU 39

The NIBE IU immersion heater range offers a robust and flexible electric heating option for cylinders, accumulator tanks and buffer vessels. Constructed using high quality tubular copper, the heaters are designed for long service life in sealed heating and hot water systems. Installation is straightforward thanks to the standardised thread and compact heater design, making the IU range suitable for both primary electric heating and backup or supplementary heating within NIBE systems. IU 6 is available at 6kW output.

NIBE IU 311

The NIBE IU immersion heater range offers a robust and flexible electric heating option for cylinders, accumulator tanks and buffer vessels. Constructed using high quality tubular copper, the heaters are designed for long service life in sealed heating and hot water systems. Installation is straightforward thanks to the standardised thread and compact heater design, making the IU range suitable for both primary electric heating and backup or supplementary heating within NIBE systems. IU 9 is available at 9kW output.

NIBE IU 34

Electric heating element

NIBE VPB 500-1000

The NIBE VPB 500/750/1000 is an efficient, copperlined hot water tank with a wide range of applications which is developed for connection to a heat pump, gas or oil boiler. The NIBE VPB 500/750/1000 has insulation made of Neopor and polyester fleece, which provides low energy loss. The insulation and outer shell are detachable to facilitate installation. The NIBE VPB 500/750/1000 is designed for buildings with large hot water requirements and can be connected in parallel for maximum capacity.

NIBE VST 11

Provides the heat pump together with SMO 10 to prioritise hot water charging on systems with floating condensing. This also requires a hot water accumulator, for ex. NIBE VPA. Hot water control for max.electric charge output: 18 kW

NIBE ELK 42

Back-up electric immersion heater - 42kW

NIBE ELK 26

Back-up electric immersion heater - 26kW

NIBE EMK 300

The NIBE EMK 300 energy metering accessories provides installers with a reliable way to monitor the actual energy delivered by a NIBE heating system, measuring both flow and temperature difference within the charge circuit to determine output for heating, domestic hot water or additional climate zones. The kit includes a precision flow meter, pre-terminated communication cable and the necessary pipework and unions for straightforward installation. The EMK 300 is suitable for lower-flow systems.

NIBE ELK 213

The NIBE ELK 213 acts as source of supplementary heat for NIBE heat pump systems, for up to 13kW output. It integrates seamlessly with NIBE systems, allowing the heat pump to activate electric backup automatically during peak loads, cold weather or rapid reheat periods. Multi-stage output control ensures smooth modulation and avoids unnecessary electrical demand. It also incorporates built-in safety features, including thermostats, temperature limiters and circuit protection, making the range suitable for compliant, predictable and installer-friendly system design.

NIBE SOLAR 42

NIBE SOLAR 42 enables solar heating with your heat pump. With additional solar panels and VPBS you get a complete system.

NIBE ELK 15

Three phase back-up electric immersion heater - 15kW

NIBE MODBUS 40

A NIBE heat pump can be controlled and monitored by external Modbus equipped equipment.

NIBE RTS 40

Room sensor used to obtain a more even indoor temperature. RTS 40 has up to three functions: Show current room temperature in the heat pump's display. Option of changing the room temperature in °C. Makes it possible to change/stabilise the room temperature.

NIBE POOL 40

The NIBE POOL 40 accessory provides a complete, ready-engineered solution for integrating pool heating into a NIBE ground source heat pump system. Using its dedicated AXC module, motorised 3-way valve and paired pool sensors, the unit automatically diverts heating medium flow through a pool heat exchanger whenever pool heating is enabled. The accessory controls both the pool circulation pump and any required external heating medium pump, ensuring correct flow and accurate temperature readings throughout the charge cycle. Built-in sensor validation ensures pool heating only activates under safe conditions, providing dependable operation and seamless interaction with the wider heat pump system.

NIBE HR 20

NIBE RMU 40

With RMU 40 you can control and monitor your Nibe heat pump from another room in the house.

NIBE HR 10

Auxiliary relay HR 10 is a connection box housing a contactor and a rotary selector switch. It is used to control external 1 to 3-phase loads such as oil burners, immersion heaters and pumps.

NIBE HTS 40

HTS 40 is an accessory that records humidity and temperature.

NIBE EME 20

Communication module that translates Modbus RTU, from a solar inverter, to Modbus TCP/IP, for the heat pump to control the solar inverter

NIBE ECS 40

ECS 40 is used when heat pump is installed in houses with up to four different climate systems that require different flow line temperatures, for example, in cases where the house has both a radiator system and an under floor heating system.

NIBE ECS 41

The NIBE ECS 41 kit allows installers to add one or more additional heating circuits to a NIBE heat pump installation where different supply temperatures are required, such as radiator and underfloor heating combinations. Each kit includes a dedicated AXC accessory module, shunt valve, shunt motor, circulation pump and temperature sensor, enabling the new zone to run as a fully controlled climate system with independent flow temperature, heating curve and pump operation. The ECS 41 is sized for larger UFH areas above 80 m².