NIBE SMO S40

NIBE RMU S40

The NIBE RMU S40 is a room unit with 2,8” touch display with built in temperature and humidity sensors. It is used to control and monitor your NIBE S series heat pump/indoor module from another room in the house than the room where the heat pump is placed. The NIBE S Series is a natural part of your connected home. Smart technology adjusts the indoor climate automatically while you’re in complete control from your phone or tablet. Giving maximum comfort and minimum energy consumption, while doing nature a favour at the same time.

NIBE IU

Electric heating element

NIBE EMK 500

Energy measurement kit for indoor unit.

NIBE ELK 15

ELK 15 is an immersion heater primarily intended for installation together with heat pump for heating. NIBE ELK 15 contains overheating protection and contactors to externally regulate the two power groups, 5.0 and 10.0 kW.

NIBE ELK 26

ELK 15 is an immersion heater primarily intended for installation together with heat pump for heating houses or

NIBE ELK 42

Electric boilers for additional heating for ground source heat pumps.

NIBE ELK 213

The NIBE ELK 213 is an electric heater designed for heating detached houses or smaller rental homes, as well as indirect heating of hot water. The NIBE ELK 213 can be installed together with a boiler, accumulator tank or heat pump. When installed together with a heat pump, for example, the electric heater automatically switches on to provide supplementary heating when the heating demand is greater than the heat pump’s capacity.

NIBE ECS 40

ECS 40 is used when heat pump is installed in houses with up to four different climate systems that require different flow line temperatures, for example, in cases where the house has both a radiator system and an under floor heating system.

NIBE ECS 41

Extra heating circuit (recommended 80-250 m2 floor heating). ECS 41 is used when heat pump is installed in houses with up to four different climate systems that require different flow line temperatures, for example, in cases where the house has both a radiator system and an under floor heating system.

NIBE S135

The NIBE S135 is an exhaust air module designed for docking to a NIBE air/water heat pump and a NIBE VVM indoor module or NIBE SMO control module. The NIBE S135 uses the heat that is found in the house’s ventilation air to heat the house and hot water, at the same time as ventilating the house. In installations with cooling, hot water and cooling can be produced at the same time. The exhaust air module provides an improved seasonal performance factor and has a low noise level and high ventilation capacity. The NIBE S135 is easy to control through the heat pump’s indoor module.

NIBE HR 10

Auxiliary relay HR 10 is a connection box housing a contactor and a rotary selector switch. It is used to control external 1 to 3-phase loads such as oil burners, immersion heaters and pumps.

NIBE EME 20

Communication and control. EME 20 is used to enable communication and control between the inverter for solarcells and heat pump/indoor module/control module.

NIBE K11

Connections box with thermostat and overheating protection

NIBE CPD 11

NIBE POOL 40

An accessory that allows pool heating using heat pump. Max 17 kW. The heat pump controls the reversing valve, pool circulation pump and any heating circuit circulation pumps via POOL 40.

NIBE AXC 30

Accessory card.

NIBE VPA/VPAS

The NIBE VPA/VPAS is a double jacket hot water tank and accumulator tank with a large water tank which is primarily designed for connection to heat pumps or other heat sources. The NIBE VPA/VPAS has a copper or enamel corrosion-resistant coating. The NIBE VPA/VPAS can handle temperatures of up to 90°C and is equipped with a socket for an immersion heater as well as a temp sensor tube. The environmentally-friendly, efficient insulation provides the tank with very low energy loss. The insulation is detachable to facilitate installation. The NIBE VPAS in size 300/450 has a copper finned coil of 2.3 m² for connection of up to 15 m² solar panels. The NIBE VPA is available in three sizes; 200/70, 300/200 and 450/300.

NIBE VPB 500-1000

The NIBE VPB 500/750/1000 is an efficient, copperlined hot water tank with a wide range of applications which is developed for connection to a heat pump, gas or oil boiler. The NIBE VPB 500/750/1000 has insulation made of Neopor and polyester fleece, which provides low energy loss. The insulation and outer shell are detachable to facilitate installation. The NIBE VPB 500/750/1000 is designed for buildings with large hot water requirements and can be connected in parallel for maximum capacity.

NIBE VPB S200

The NIBE VPB S200 is an efficient hot water tank which is designed for connection to a heat pump, gas or oil boiler. The NIBE S200 can also be docked to solar panels. The NIBE VPB S200 has insulation made of polyurethane, which provides very good heat insulation.

NIBE VPB S300

The NIBE VPB S300 is an efficient hot water tank which is designed for connection to a heat pump, gas or oil boiler. The NIBE S300 can also be docked to solar panels. The NIBE VPB S300 has insulation made of polyurethane, which provides very good heat insulation.

NIBE VST 20

Makes hot water priority possible at large heat pump outputs. (charging power between 15 and 40 kW), together with an SMO 10 and F1330-40. This also requires a hot water accumulator, for example, NIBE VPA.

NIBE VST 11

Provides the heat pump together with SMO 10 to prioritise hot water charging on systems with floating condensing. This also requires a hot water accumulator, for ex. NIBE VPA. Hot water control for max.electric charge output: 17 kW